Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - RussWilliams

Pages: [1]
1
Feature Requests and Suggestions / Add X-mouse capability
« on: April 03, 2013, 22:59:38 »
I would really like to have X-mouse work with the Explorer Panels of MC. I use X-mouse on my system, which allows me to hover my mouse over a window and scroll it without clicking to give it focus. In MC, I keep trying to hover the mouse over the Explorer Panel that does not have focus and scroll that panel. Needless to say, it doesn't work, but I wish it did. Is there any possibility for such a thing?

2
Support and Feedback / Button Panel Puzzlement
« on: October 13, 2012, 18:12:19 »
I have a puzzling problem with the button panel. It's not critical, but I would like to get a solution.
I installed a substitute Windows start menu called "Classic Start Menu". One of its options is to open it by hovering over the Start button. I use this a lot, but after doing that, I find that the MC button panel display has switched to the CTRL+ display. (I keep MC open all the time.) This is not critical, since I only have to right-click in the button panel to restore it, but it would be nice if the button panel display would restore itself after I stop hovering over the Start button.
I'm not sure if Classic Start Menu is causing this, or if MultiCommander could do something to keep this from happening. Any thoughts?  :-\

3
Beta Releases / Hotkeys for View Modes
« on: September 19, 2012, 17:22:58 »
How do you assign a hotkey to a View Mode?

4
Is there an easy way to drag'n'drop the current folder on a button in the button panel? I have tried to D&D the current tab, or a subfield from the current path field, but neither one works. It's a pain to have to go up to the parent folder and then look for the subfolder you were just in.

5
Support and Feedback / Hot Path Icon shows wrong tool tip
« on: November 05, 2011, 21:59:58 »
When you bring up the Hot Path list (by right-clicking in the path field) and then hover the mouse over the icon that looks like a rectangle with a plus sign superimposed, a tooltip is shown that says "Set current path to this Hot Path". What it should really say is "Set this Hot Path to the current path".

6
Feature Requests and Suggestions / Highlight Toolbar Name
« on: October 10, 2011, 22:47:45 »
I would like to see the name highlighted for the current toolbar showing (i.e. Address, Standard, Drives, File Commands). It would be nice to have something show which toolbar is displayed.

7
Feature Requests and Suggestions / Remember position on restart
« on: October 09, 2011, 16:21:07 »
I wish MultiCommander would remember the position(s) it was at when it was last shut down, and reposition there at startup. Is there a setting somewhere that will do that?

8
Feature Requests and Suggestions / Better horizontal scrolling
« on: September 27, 2011, 21:46:48 »
When I click on "Show Folder Tree", it subdivides the panel into two sections, the folder tree and the file list within the current folder, as expected. However, the horizontal scroll bar under the file list cannot be moved left to display the beginnings of the file names, and usually I am left seeing only the file extensions and subsequent columns. I would really like this to be fixed.

9
Support and Feedback / Favorites/Bookmarks
« on: September 17, 2011, 17:20:59 »
Is there some way to create a Favorites list or Bookmarks?

10
Support and Feedback / "Page Not Found" in Documebntation
« on: August 01, 2011, 21:46:25 »
In the documentation, Functions->Explorer Panel->Folder Tree causes a "Page Not Found" error. Is the information about folder trees found anywhere else?

11
Support and Feedback / How do I change the default editor?
« on: August 01, 2011, 17:49:47 »
I tried to change the default file editor (Configuration->File Editor Setup), but it does not seem to work. F9 still uses Notepad, and when I go back to Configuration->File Editor Setup, it has changed the default back to Notepad. How do I make the change persist?

12
Support and Feedback / How do I use tabs?
« on: August 01, 2011, 17:14:15 »
The web site indicates that tabs can be used, but I can't find any description in the documentation.

Pages: [1]